PRODUCT OVERVIEW
The VisionRGB-E1S has a single video capture device supporting up to 1920x1080 DVI or 2048x1536 analog resolution.
The VisionRGB-E1S captures the Analog/ DVI data and triple buffers it into onboard storage. This data is then copied using DMA to the host system for display, storage or streaming.
When a Datapath graphics card is used, the VisionRGB-E1S transfers the data directly to the graphics card thereby increasing performance. The VisionRGB-E1S capture card sends the relevant portions of each captured image to each display channel and instructs each channel to use its graphics engine to render the data. This fully utilises the hardware and dramatically increases performance.
When the RGB/DVI data is displayed on a non Datapath graphics card, the VisionRGB-E1S sends the data to system memory or direct to the graphics card, dependant on the software used for display.
The VisionRGB-E1s is an ideal solution for applications that require the capture of analog or DVI sources in real time. Typical applications include:
Viewing Analog or DVI sources from PCs, MACs, Industrial/medical equipment, cameras and other video equipment
Streaming video applications
Video wall controllers
RGB STREAMING
The VisionRGB-E1S is an ideal solution for applications that require the capture of analog or DVI sources in real time. Typical applications include:Viewing analog or DVI sources from PCs, MACs, Industrial/medical equipment, cameras and other video equipment Streaming video applications and video wall controllers.
VIDEO STREAMING SUPPORT
Direct WDM streaming driver supports the following applications, to encode, record and stream video over networks or the internet:
Dataton WatchOut
Microsoft Expression Encoder
Microsoft Windows® Media Encoder
VideoLAN VLC
NorPix StreamPix
VitualDub
Adobe Flash Encoder
VidBlaster
AMCap and other DirectShow compatible software
For further details see the Datapath DirectShow SDK documentation supplied as part of a typical installation.
SOFTWARE
The VisionRGB-E1S video capture card is supplied with a powerful software application for configuring the timing and format of the input sources and displaying the data. Simply connect your external DVI or Analog source into the card, run the VisionRGB-E1s application to automatically detect the video source format and display the captured video in a window on your desktop.
Datapath Vision RGB-E1S Capture Card
4 lane PCI Express interface with maximum data rate of 650MB/sec
Max analog RGB video capture resolution of 2048 x 1536 x 24bit
Max DVI capture resolution of 1920 x 1200 x 24bit and 1920 x 1080 x 32bit at 60Hz
SPECIFICATION FOR THE VisionRGB-E1S VIDEO CAPTURE CARD:
Board format
PCI Express x4 low profile card, 68.9mm x 167.6mm
PCI Express bus master with scatter gather DMA providing
Maximum data rate of 650MB/s
Connectors One DVI-I type connector
Maximum sample rate
170 MHz analogue RGB or 165 MHz DVI
Analog modes up to 340MHz pixel clock can be captured using dual-pass sampling
Video sampling RGB: 24bits per pixel/ 8-8-8 format
Video capture memory 32MB, triple buffered
Analog RGB mode support 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024, 1600 x 1200, 1920 x 1080, 2048 x 1536, custom modes
DVI single-link mode support 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024, 1600 x 1200, 1920 x 1080, 1920 x 1200, custom modes
HD modes 1080p, 1080i, 720p, 576p, 576i, 480p and 480i using a Component-DVI connector (HDCP not supported)
Input mode detection Automatic detection of input modes in hardware, enabling the tracking of mode changes in the source signal
Pixel transfer formats
RGB: 5-5-5, 5-6-5 or 8-8-8 (24bit/32bit) pixels
YUV: 4:2:2
MONO: 8bits
Update rate
User defined, captured frame rate will match the source. Providing max data rate (650MB/s) is not exceeded
Multi-buffered to eliminate tearing artifacts
Video format options
Analog RGB plus HSync and VSync (5 wire)
Analog RGB with Composite Sync (4 wire)
Analog RGB with Sync on Green/ YPbPr (3 wire)
DVI Single Link
Operating system support Windows® XP, Windows® Vista, Windows® Server 2003, Windows® Server 2008, Windows® 7, Windows® 8 and Linux, Windows® Server 2012 (NOTE: Check Linux specific features with Sales)
Power requirements
Max current at +3.3V - 0.25A
Max current at +12V - 0.5A
Max power - 6.8 Watts
Operating temperature 0 to 35 deg C/ 32 to 96 deg F
Storage temperature -20 to 70 deg C/ -4 to 158 deg F
Relative humidity 5% to 90% non-condensing
Warranty 3 years
We are continously developing the technology used within our product ranges deliverying outstanding innovative solutions, therefore the specification may change from time to time.
Scroll Down For More
USD $1013.00 Status: In-Stock
Board Model 139 139B 139C 139D 139E
Free Freight !
